series p internationally approved toggles www.nkk.com a90 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt a toggles general specifcations electrical capacity resistive load: 10a @ 125v ac or 6a @ 250v ac motor load: 400w @ 125v ac lamp load: 2a @ 125 v ac for on-off-on circuit & 3a @ 125v ac for other circuits other ratings contact resistance: 10 milliohms maximum insulation resistance: 1,000 megohms minimum @ 500v dc dielectric strength: 2,000v ac minimum between contacts for 1 minute minimum; 4,000v ac minimum between contacts & case for 1 minute minimum mechanical life: 100,000 operations minimum electrical life: 25,000 operations minimum angle of throw: 25 materials & finishes toggle cap : brass with nickel plating lever: brass with chrome plating bushing: brass with nickel plating frame: stainless steel case/base: diallyl phthalate resin (ul94v-0) movable contacts: silver alloy with silver plating stationary contacts: pure silver with silver plating terminals: copper with silver plating environmental data operating temp range: C10c through +85c (+14f through +185f) humidity: 90 ~ 95% humidity for 96 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours shock: 50g (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) installation soldering time & temp: wave soldering recommended (straight pc): see profle a in supplement section. manual soldering: see profle a in supplement section. cleaning: these devices are not process sealed. hand clean locally using alcohol based solution. standards & certifications flammability standards: ul94v-0 rated case/base ul: file no. e44145 - recognized only when ordered with marking on switch. add /u or /cul to end of part number to order ul recognized switch. all models recognized at 10a @ 125v ac & 6a @ 250v ac. csa: file no. 023535_0_000 - certifed only when ordered with marking on switch. add /c to end of part number to order csa certifed switch. all models certifed at 10a @ 125v ac & 6a @ 250v ac. vde: license no. 119174 all models approved at 10a @ 125v ac & 6a @ 250v ac. marking on switch is standard. all models meet en 61058-1 standard.
series p internationally approved toggles www.nkk.com a91 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable a toggles rockers touch tilt distinctive characteristics actual size meets en 61058-1 standard. high torque bushing construction prevents rotation or separation from frame during installation. stainless steel frame resists corrosion and increases environmental safety. case/base of heat resistant resin meets ul94v-0 fammability standard. contacts of special silver alloy resist arcing and guarantee stable electrical contact and long life. high insulating barriers increase isolation of circuits in double pole devices and provide added protection to contact points. prominent external insulating barriers increase insulation resistance and dielectric strength. epoxy sealed terminals prevent entry of fux, solvents, and other contaminants. clinching of the frame to the case well above the base and terminals provides 4,000v dielectric strength.
series p internationally approved toggles www.nkk.com a92 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt a toggles 22 terminals no code solder lug* p straight pc z .187 (4.75mm) quick connect typical switch ordering example p20 dpdt on-none-on circuit poles & circuits 11 spst on none off 12 spdt on none on 13 spdt on off on 21 dpst on none off 22 dpdt on none on 23 dpdt on off on toggles & bushings no code .512 (13.0mm) white cap with 6mm bushing e .450 (11.4mm) flatted with 6mm bushing b .689 (17.5mm) large bat with 12mm bushing d .748 (19.0mm) white capped column with 12mm bushing description for typical ordering example P2022B b .689 (17.5mm) large bat with 12mm bushing solder lug terminals toggle position connected terminals throw & schematics pole model down center up down center up note: terminal numbers are on the switch. sp p2011 on none off 1-1b open open spst sp p2012 p2013 on on none off on on 1-1b open 1-1a spdt dp p2021 on none off 1-1b 2-2b open open dpst dp p2022 p2023 on on none off on on 1-1b 2-2b open 1-1a 2-2a dpdt poles & circuits 1 (com) 1b 1 (com) 1b 1a 1 2 (com) 1b 2b 1 1b 2b 2 (com) 1a 2a keyway keyway * wire harness & cable assemblies offered only in americas important: vde is marked on all models. switches are supplied without ul, culus & csa marking unless specifed. ul, culus & csa recognized only when ordered with marking on the switch. specifc models, ratings, & ordering in- structions are noted on general specif- cations page.
series p internationally approved toggles www.nkk.com a93 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable a toggles rockers touch tilt (6.35) .250 (1.3) dia .051 (4.75) .187 (9.0) .354 thk = (0.8) .031 epoxy seal (4.5) .177 (2.6) .102 (1.25) .049 (2.0) .079 thk = (1.0) .039 (7.6) .299 (1.17) .046 thk = (1.0) .039 epoxy seal (4.8) .189 toggles & bushings e panel thickness with keyway .134 (3.4mm) maximum for 6mm bushing : 1 locking ring at507m, 1 internal tooth lockwasher at509, 2 hex nuts at513m for 12mm bushing : 1 hex face nut at503m, 1 locking ring at506m, 1 internal tooth lockwasher at508, 1 hex mounting nut at527m optional splashproof boot assemblies (for code b) : at401 & at4181 boots plus hex nut & o-ring; see accessories & hardware section. .450 (11.4mm) flatted with 6mm bushing no code .689 (17.5mm) large bat with 12mm bushing terminals solder lug b d .748 (19.0mm) white capped column with 12mm bushing .512 (13.0mm) white cap with 6mm bushing panel cutouts panel thickness with locking ring .102 (2.6mm) maximum panel thickness with keyway .256 (6.5mm) maximum panel thickness with locking ring .217 (5.5mm) maximum standard hardware z p no code .187 (4.75mm) quick connect straight pc (12.5) dia .492 (11.5) .453 (1.5) .060 (9.0) .354 (12.5) dia .492 (3.0) dia .118 (6.35) dia .250 (5.6) .220 (0.6) .024 (6.35) dia .250 (6.5) .256 (2.2) dia .087 typical switch dimensions p2011 models do not have terminal 1a. p2012 p2021b, P2022B, p2023b 12mm bushing p2011, p2012, p2013 6mm bushing spst spdt dpst dpdt p2021 models do not have terminals 1a & 2a. P2022B (5.08) .200 (10.16) .400 (1.8) dia ty p .071 (7.62) ty p .300 1 1a 2a 2 1b 2b (10.16) .400 (1.8) dia ty p .071 (7.62) ty p .300 1 2 1b 2b (1.8) dia ty p .071 (7.62) ty p .300 1 1b (1.8) dia ty p .071 (7.62) ty p .300 1 1a 1b 25 (13.0) .512 (4.2) dia .165 25 (11.4) .450 (2.54) .100 (17.5) .689 25 (6.0) dia .236 (19.0) .748 25 (4.4) dia .173 1b 1a 1 (20.5) .807 (2.6) .102 keyway (11.0) .433 (13.0) .512 (8.0) .315 (7.62) .300 m6 p0.75 (0.5) .020 (0.8) .031 (5.0) .197 25 (4.2) dia .165 (22.0) .866 (1.0) ty p .039 (1.25) x (2.0) ty p .049 x .079 (0.9) .035 1 2 2a 1a 1b 2b (10.16) .400 (20.5) .807 (2.6) ty p .102 keyway (20.0) .787 m12 p1 (7.62) .300 (0.5) .020 (0.8) .031 (5.0) .197 25 (6.0) dia .236 (17.5) .689 (12.0) .472 (21.1) .831 (1.0) ty p .039 (1.25) x (2.0) ty p .049 x .079
|
